STEPPERONLINE 1.5KW 220V 2HP 7A VFD Variable Frequency Drive Inverter Controller

Description

Store Categories
Store Categories
Open Loop Motor
Nema 8 (20mm)
Nema 11 (28mm)
Nema 14 (35mm)
Nema 16(39mm)
Nema 17 (42mm)
Nema 23 (57mm)
Nema 24 (60mm)
Nema 34 (86mm)
Open Loop Driver
Nema 17 Driver
Nema 23 Driver
Nema 24 Driver
Nema 34 Driver
Open Loop Stepper Kit
Nema 23 Stepper Kit
Nema 34 Stepper Kit
VORON V0.1
Closed Lopp Stepper Kit
Nema 17--0.72Nm
Nema 23--1.2Nm
Nema 23 -- 2Nm
Nema 24 -- 3Nm
Nema 24--4Nm
Nema 34 -- 4.5Nm
Nema 34--4.8Nm
Nema 34--9Nm
Nema 34--12Nm
Nema 23--3Nm
Closed Loop Driver
Closed Loop Motor
Integrated Servo Motor
AC Servo Motor Kit
VFD Variable Frequency Drive
1.5KW
2.2KW
3.7KW
5.5KW
7.5KW
Spindle Motor
Air Cooled
Water Cooled
MEAN WELL Power Supply
Enclosed Type
DIN Rail Power Supply
LED Power Supply
Power Supplies
Worm Gearbox
Output Shaft for NMRV030
Output Shaft for NMRV040
Planetary Gearbox
Geared Stepper Motor
Nema 17 Geared
Nema 23 Geared
Precision Planetary Geared
BLDC Motor
BLDC Driver
Linear Stepper
Motor Mounting Brackets
Stepper Motor Cable
New Arrival
Top Selling Products
Clearance Sale
Other
This VFD with power 2HP(1.5KW) and single phase 220V input voltage. The H100 series is General Variable Frequency Drive(VFD), they are widely used in application of: Textile machines, Packaging machines, Engraving machines, Printing machines, Food machinery, Woodworking machinery, Pump fans, Ceramic machinery, Solar pumps and others.
This product has V/F control, speed sensor less vector control, etc., suitable for asynchronous motors, permanent magnet
synchronous motors, single-phase motors. H100 series inverter have compact structure, convenient and flexible installation,reasonable heat dissipation design to ensure product reliability, rich keyboards and multi-function cards to choose, flexible functions.
Package Content
1 x 1.5KW Variable Frequency Drive Inverter
1 x English Manual
Key Specification
Rated Input Voltage: 1-Phase 200~240VAC
Allowed Input Voltage: 180~260VAC
Input Frequency: 50/60Hz(+/-5%)
Input Current: 14.0A
Power: 2HP(1.5KW)
Output Current: 7.0A
Output Voltage: 0~Rated Input Voltage
Output Frequency: 0~1000Hz
Output Capacity: 150% Rated Current 60s, 180% Rated Current 2s
Main circuit and function card
Power terminal wiring instructions
For 220V class inverter, use class 3 grounding method(grounding resistance: less than 100Ω).
Use special grounding terminal for grounding. Do not use screws for grounding in the box.
Note: Grounding steps
(1) Determine the location of the ground terminal.
(2) Connect the ground-wire to the ground terminal and make sure that the screws are tight
Main circuit terminal description
Please implement the wiring in accordance with the regulations of electrician regulations to ensure safety
When selection of the wire diameter specification ● It is best to use isolated wires or conduits for power wiring, and ground the isolation layer or conduits at both ends.
● Be sure to install the air disconnect switch NFB between the power supply and the input terminals(R / L1, S / L2, T / L2)
● Do not connect the AC power supply to the output terminal (U V W) of the inverter.
● The output wiring must not touch the metal shell of the inverter, in case of a short circuit to ground.
● Do not use phase shift capacitors, LC / RC noise filters and other components at the output of the inverter.
● The main circuit wiring of the inverter must be far away from other control equipment.
● When the wiring between the inverter and the motor exceeds 15 meters (220V level),(380V level 30 meters), a high dV / dT will be generated inside the motor coil, which will produce interlayer insulation of the motor then damaged, please use a special motor for the inverter or install a reactor on the inverter side.
Keyboard Features